ipv6

Diagnose ipv6 address anycast

Firmware – FortiOS: 5.0 5.2 5.4
This command is used to add IPv6 anycast address.

Syntax
diagnose ipv6 address anycast

Diagnose ipv6 gre-tunnel list

Firmware – FortiOS: 6.0
This command is used to show a listing IPv6 GRE tunnels within the active VDOM. It the the ipv6 equivalent of diagnose ip gre-tunnel list.

Syntax
diagnose ipv6 gre-tunnel list

Example
diagnose ipv6 gre-tunnel list

devname=gre6 devindex=17 ifindex=53 vfid=0003 ref=0
laddr=2003:172:16:200::1 raddr=2003:172:16:201::2
key=0/0 flags=0/0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b);
RX packets:0, TX packets:0, TX carrier_err:0 collisions:0

total tunnel = 1

Diagnose ipv6 ipv6-tunnel

Firmware – FortiOS: 5.0 5.2 5.4

Syntax
diagnose ipv6 ipv6-tunnel add – Add tunnel.
diagnose ipv6 ipv6-tunnel delete – Delete tunnel.
diagnose ipv6 ipv6-tunnel list – Show tunnels.

Diagnose ipv6 router rip

Firmware – FortiOS: 5.0 5.2 5.4

All
Use this command to enable/disable all rip router settings.

level info
Use this command to set the debug level to information, a verbose reporting level.

Syntax
diagnose ipv6 router rip all — Enable all debugging.
diagnose ipv6 router rip events — RIPng events.
diagnose ipv6 router rip level critical — Critical level.
diagnose ipv6 router rip level error — Error level.
diagnose ipv6 router rip level info — Information level.
diagnose ipv6 router rip level none — None level.
diagnose ipv6 router rip level warn — Warning level.
diagnose ipv6 router rip packet-receive — RIPng receive events.
diagnose ipv6 router rip packet-send — RIPng send events.
diagnose ipv6 router rip show — Show status of RIPng debugging.

Command
diagnose ipv6 router rip level info

Output

:dev=lo mac=00:00:00:00:00:00 rx_tcp_mss=0 tx_tcp_mss=0 overspill-threshold=0 bytes=0 over_bps=0 sampler_rate=0
:dev=dummy0 mac=00:00:00:00:00:00 rx_tcp_mss=0 tx_tcp_mss=0 overspill-threshold=0 bytes=0 over_bps=0 sampler_rate=0
:dev=internal mac=00:00:00:00:00:00 rx_tcp_mss=0 tx_tcp_mss=0 overspill-threshold=0 bytes=0 over_bps=0 sampler_rate=0
:dev=wan1 mac=00:00:00:00:00:00 rx_tcp_mss=0 tx_tcp_mss=0 overspill-threshold=0 bytes=0 over_bps=0 sampler_rate=0
:dev=wan2 mac=00:00:00:00:00:00 rx_tcp_mss=0 tx_tcp_mss=0 overspill-threshold=0 bytes=0 over_bps=0 sampler_rate=0
:dev=dmz mac=00:00:00:00:00:00 rx_tcp_mss=0 tx_tcp_mss=0 overspill-threshold=0 bytes=0 ove

Command
diagnose ipv6 router rip show

Output

:RIPng debugging status:
::RIPng event debugging is on
::RIPng packet detail debugging is on
::RIPng NSM debugging is on
::RIPng debugging level is CRITICAL